2803IN / SEW - Taiwan
- Test voltage (DCV): 0.5kV/1kV/2.5kV/5kV
- Measurement range: 0-25GΩ / 0-50GΩ / 0-125GΩ / 0-250GΩ
- Accuracy: 0-50GΩ : ±3% rdg; 50-250GΩ : ±5% rdg
- Dimensions: 170(L) × 120(W) × 95(D)mm
- Weight: 930g
- Power: 1.5V(AA) × 8
- Standard: EN 61010-1 ; EN 61326-1

T-GIK 01 / NOVAX (Malaysia)
- A handheld device that assists users in the process of visually inspecting abrasions, cuts, tears or punctures on insulating gloves
- Glove inflator set includes: Test pump, a carrying bag, and a strap to hold the gloves in place during testing
- Total weight: Approx. 0.9kg
- Recommendation: you should use a pump to check insulating rubber gloves before using them in contact with electricity, to ensure safety and avoid the gloves being exposed, punctured, eroded, etc., causing leaks. Dangerous electricity.

290HD / SEW - Taiwan
- Test voltage range: 6kV~81.5kV
- Operating voltage: 2.7kV (Compared to ground)
- Display: Red light, Sound 50dB at 3m
- Club length: 1370±50mm (retracted) and 2450±50mm (extended)
- Frequency: 50/60Hz
- Withstand voltage: 100kV/300mm for 1 minute
- Insulation resistance: 2000MΩ min at 1kV
- Detection current: 100uA or less than 100uA
- Operating temperature: 0°C~40°C
- Battery source: 2 button-cells LR44 (1.5V)
- Weight: 590g (including battery)
- Standard: IEC / EN 61243-1

230HD / SEW - Taiwan
- Test voltage range: 6kV ~ 36.5kV
- Operating voltage: 2.7kV (Compared to GND)
- Display: Red light, Sound 50dB at 3m
- Club length: 893±50mm (retracted) and 1520±50mm (extended)
- Frequency: 50/60Hz
- Withstand voltage: 100kV/300mm for 1 minute
- Insulation resistance: 2000MΩ min at 1kV
- Detection current: 100uA or less than 100uA
- Operating temperature: 0°C~40°C
- Battery source: 2 button-cells LR44 (1.5V)
- Weight: 485g (including battery)
- Standard: IEC / EN 61243-1

DVM-80UVM / HD Electric - USA
- Operating Voltage: 50V - 40kV (Up to 80kV with additional resistor)
- Operating Temperature: –25°C to +55°C
- Operating Frequency: 50-1000Hz AC/DC
- Backlit LCD display, easy to read in low light or dark conditions
- Fiberglass Rod Diameter: 1”(2.54cm)
- Connection Cord Length: 12'(3.6m) when extended; 3.5'(1.7m) when retracted
- Dimensions: Length (without probe): 15”(38cm)
- Weight (without probe): 1.02kg

PD800IW is a wireless phase isotope tester designed for convenient phase angle testing, easy to use because it does not require connecting cables between probes. The device includes a probe and a reference probe that are connected via wifi and will operate reliably at distances of up to 100 feet (30 meters). The device can use voltage levels from 120V to 800kV
Specifications
- Type: PD800W.
- Place of manufacture: Bierer Associates Inc (USA).
- Use indoors and outdoors.
- Operating temperature: -100C to +500C.
- 9V rechargeable battery with removable charger 220V/50Hz.
- LED screen displays phase difference angle.

- A handheld device that assists users in the process of visually inspecting abrasions, cuts, tears or punctures on insulating gloves
- Glove inflator set includes: Test pump, a carrying bag, and a strap to hold the gloves in place during testing
- Total weight: Approx. 0.9kg
- Recommendation: you should use a pump to check insulating rubber gloves before using them in contact with electricity, to ensure safety and avoid the gloves being exposed, punctured, eroded, etc., causing leaks. Dangerous electricity.

Accutest ACC8901 - used to measure wind speed
- LCD screen with light
- Dimensions 45 x 72 x 35mm
- Weight: 275g
- Air speed measurement: 0 ~ 45 m/s, 0 ~ 140 km/h, 0 ~ 8800 ft/min, 0 ~ 88 knots, 0 ~ 100 mph (± 3%)
- Air temperature measurement: 0 ~ 45oC, 32 ~ 113oF (± 2oC)
- Resolution: 0.2oC, 0.1 m/s
- Speed units: m/s, ft/min, knots, km/hr, mph
- Low battery notification sign: yes
- Auto off: 14 minutes without any operation
- Backlight technology: 12 seconds of operation by pressing any key
- MAX/MIN/AVG reading feature. Convert temperature back and forth between degrees Celsius and degrees Fahrenheit

DT4282 / HIOKI - Japan
- DC voltage measurement feature: 60 mV to 1000 V, 6 scales
- AC voltage measurement feature: 60 mV to 1000 V, 6 scales
- DC / AC voltage measurement mode: 6V to 1000 V, 4 scales
- DC current measurement feature: 600 μA to 10 A, 6 scales
- AC current measurement feature: 600 μA to 10 A, 6 scales
- Resistance measurement feature: 60 Ω to 600 MΩ, 8 scales
- Capacitance measurement feature: 1 nF to 100 mF, 9 ranges
- Check continuity: 20/50/100/500 Ω
- Diode test:  Open terminal voltage: ≤4.5 V, Test current: ≤1.2 mA

IR3455 / Hioki - Japan
-  Test voltage: 250 V to 5.00 kV DC
- Voltage measurement:
0.00 MΩ to 500 GΩ (250 V)
0.00 MΩ to 1.00 TΩ (500 V)
0.00 MΩ to 2.00 TΩ (1 kV)
0.00 MΩ to 5.00 TΩ (2.5 kV)
0.00 MΩ to 10.0 TΩ (5 kV)
- Current measurement: 1 mA
- Resistance range: 10 MΩ to 10 TΩ, 7 scales
- Leakage measurement: 1.00 nA to 1.20 mA, 6 scales
- Voltage measurement: ±50 V to ±1.00 kV DC, 50 V to 750 V AC

IR4056-21 / Hioki - Japan
- Output measurement voltage: 50/125/250/500/1000 VDC
- Maximum resistance measurement value: 100/250/500/2000/4000 MΩ
- Lower limit resistance value: 0.05/0.125/0.25/0.5/1 MΩ
- Overload protection: AC 600V (10s) for scales < 1000 VDC and AC 1200V (10s) for scales 1000 VDC
- DC voltage measurement feature: 4.2V to 600V, 4 scales
- AC 50/60 Hz voltage measurement feature: 420V / 600V, 2 scales
- Ground wire continuity test feature: 10 Ω to 1000 Ω, 3 scales

3125A / Kyoritsu - Japan
- AC/DC voltage measurement: 30 ~ 600V
- Short circuit current: 1.5mA
- Test voltage: 250V/500V/1000V/2500V/5000V
- Resistance measurement range: 100.0MΩ/1000MΩ/2.00GΩ/100.0GΩ/1000GΩ
- Accuracy: ±5%rdg |±3dgt, ±20%rdg (100GΩ or more)
- Power supply: DC12V: LR14/R14 × 8pcs
- Accessories: 7165A (Line probe); 7264A (Earth probe); 7265A (Guard probe); 8019 (Hook type prod) ; 9181 (Carrying case) ; LR14×8pcs (Battery) ; User manual.

3165/ Kyoritsu
- DC Test Voltage : 500V
- Max measurement value : 1000MΩ
- First measurement range : 1~500MΩ
- Error : |±5% rdg
- Second measurement range : 1/1000MΩ
- Error : ±10% rdg
- AC voltage : 600V
- Accuracy : |±3%
- Power supply : R6P (AA) (1.5V) × 4
- Dimensions : 90(L) × 137(W) × 40(D)mm
- Weight : 330g approx.